The laboratory is designed for operational control of fuels at petroleum storage bases, petrol stations.
The mobile laboratory is equipped for rapid fuel analysis. It should be noted at the outset that not all methods of analysis are arbitration, but the mobile laboratory does not aim to fully replace a stationary laboratory equipped with a complete set of equipment for classical methods of analysis.
When completing, emphasis is placed on modern, high-tech equipment that can work in the laboratory on the chassis, does not require the preparation of the sample and for a short time to give results.
The main indicators of fuel quality, implemented in the laboratory:
- distillation
- octane number (gasoline), cetane number (diesel fuel)
- turbidity, CPP, FPP
- density
- sulphur content
- content of iron, vanadium, other elements
- viscosity
- flash point
- Total pollution (particulate matter)
- specific electrical conductivity
- Pressure of saturated vapours
Mobile IR-Fourier spectrometer (with built-in density measurement module)
Compliance with the requirements: ASTM D6277, ASTM D7371, ASTM D5845, ASTM D7777, EN 238, EN 14078, ISO 15212, IP 559.
Correlation: ASTM D2699, D2700, D5191, D86, D4815, D6839, D613, D4737A, D4053, D7806, EN ISO 405, EN ISO 5164, EN ISO 5163 EN ISO 13016/1, EN ISO 3405, EN ISO 22854, EN ISO 5165, EN ISO 4264, SGS M2533
Specifications: ASTM D975, ASTM D1655, ASTM D4814, EN 228, EN 590, DEFSTAN 91-091
It allows the operator to get the result, which is interpreted according to several important indicators of fuel quality, such as distillation data, octane and cetane numbers, oxygenate content, aromatic substances, density and a number of others.
The device works from the vehicle’s on-board network or from the 220V network.
Interface - USB, LIMS. Calibrations and test results are stored in the device memory.
Automatic Low Temperature Fuel Properties Analyzer
Fully automated low-temperature analyser of fuel properties, namely the point of turbidity, CPP, FPP temperature. Modern cooling system that provides a wide temperature range from -120°C to +35°C. Cooling speed - 1°C in 5 seconds or less. Temperature maintenance accuracy 1°C.
Features:
Low power consumption.
Compact - 30 cm wide
High resolution touch screen, tablet.
Built-in, maintenance-free cooling system.
USB interface, LIMS, output to printer.
The points of turbidity and solidification are tested on the same test position
Automatic densometer
Designed for high-precision and express determination of liquid media density.
Accuracy and reproducibility - 0.0001 g/cm³
Interface - USB and Ethernet
Intuitive user-friendly software, large touch screen
X-ray fluorescence analyzer
The EXDRF is a spectrometer. Portable device in field version (with moisture protection IP44).
Determination of sulphur by ASTM D 4294 with detection limit of 3 ppm.
Determination of elemental composition in samples from Na to U (including iron and lead in motor gasolines).
Automatic portable viscometer
The instrument is designed to determine the kinematic viscosity of liquids in a mobile laboratory.
The portable viscometer, weighing 1.8 kg, is equipped with a touchscreen to control the device and is equipped with a battery for independent operation.
The analysis does not require solvents, density determination or thermometer To obtain high accuracy without prior test measurements, each sample is measured at a constant temperature.
Principle of operation: Hele-Shaw technology, which uses a folding cell with a capillary channel to determine kinematic viscosity. Infrared sensors are used to record the expiry time of the sample.
Kinematic viscosity measurement range: 1-700 mm2/s (cSt) at 40oC
Sample volume - 60 ml (3-4 drops)
Dimensions: 152x127x203 cm
Automatic Flash Point Analyzer
It is an automated flash point tester in a closed Pensky-Martens cup up to 300°C. The device uses electrical sample ignition.
Methods: ASTM D3278, ASTM D3828, ASTM D7236, ASTM E502, BS 2000-523, Rules CLP EC № 1272/2008, EPA 1020 A & B, IP 523, IP 524 (обс), IP 534, ISO 3679, ISO 3680
Sample volume - 2-4 ml
Analysis time - 7 minutes.
Color display, touch pad.
Jet fuel specific conductivity meter
The manual fuel conductivity meter complies with the requirements of ASTM D2624. It provides accurate and rapid measurement of conductivity of distillate fuels; and is specially designed for testing low conductivity liquids such as aviation kerosene.
The analyser can measure the specific electrical conductivity of the fuel from 0 to 2000 pS /m, although it is usually used in the range from 0 to 500 pS /m.
Battery, USB interface, measurement data storage.
Saturated Gasoline Vapor Pressure Analyzer
The device makes it possible to obtain quick results on the measurement of the pressure of saturated petrol vapours by the arbitration method EN 13016-1. The sample is injected through the sept into a constant volume chamber whose temperature is maintained at 37.8 °C 0.1 °C. The ratio of the vapour to the liquid phase is 4:1. The pressure in the chamber shall be measured automatically at an interval of 1 minute until three values with a difference of not more than 0.1 kPa are obtained, after which the test shall be completed.